flowermate v5 nano teardown banner

Flowermate V5 Nano Teardown and Preview

The Flowermate V5 Nano is nearing release and we’re previewing it in PuffItUp style with a full teardown! 

WARNING: Do not attempt this vape teardown, any disassembly other than the mouthpiece will void your warranty.

flowermate v5 nano teardown 1

The Flowermate V5 Nano (Last Moments) 

Here we have the Flowermate V5 Nano looking sleek and confident in its final hour. We only received two of these units so this is a difficult loss – luckily our twin Nano will help get us through these trying times.

flowermate v5 nano teardown battery port 2

Battery and Mouthpiece Compartments

The V5 Nano is the first Flowermate with a removable battery. It also keeps the V5 tradition of an integrated mouthpiece compartment in the base of the unit. The base door is held in place by a sliding lock mechanism for easy access to both the battery and clear black glass mouthpiece.

flowermate v5 nano vaporizer teardown 18560 battery 2500 mah

Flowermate V5 Nano Battery

The Flowermate V5 Nano battery is a flat top IMR 18650 battery with a 2500 mAh capacity and 20 amp maximum continuous output. A higher max output generally means a lower max capacity but the cell Flowermate chose is right in the sweet spot for both. The Nano hits vaping temp in half a minute and we get about 40-50 minutes per charge depending on temperature settings; relatively normal for single cell hybrid vapes. A full charge from completely empty will take about two and a half hours.

Reminder: Do NOT follow along past this point. Disassembly is not covered under warranty.

flowermate v5 nano teardown battery port 4

Battery Port Disassembly

The negative connection plate appears to be brass and is held in place using two screws. The smaller brass piece and spring comprise the battery door lock mechanism.

flowermate v5 nano teardown screw removal 5

Chassis Screws

Two thicker screws between the mouthpiece and battery compartments. With these bad boys out the chassis is nearly ready to remove.

flowermate v5 nano teardown slide lid removal 6

Top Plate Removal

The slide door plate is held between the inner and outer sections of the unit; now that the two portions aren’t tightly fitted together we can take it out. With the top plate removed we can access the faceplate of the V5 Nano.

flowermate v5 nano teardown display cover removal 7

The Final Piece

The faceplate is the last thing keeping us from separating the internal electronics enclosure from the protective aluminum exterior.

flowermate v5 nano teardown display removal 8flowermate v5 nano teardown screen cover and buttons

V5 Nano Face-Off

The Nano’s faceplate is held in place by 12 tabs. We shimmied each tab loose then removed the plate and two button covers beneath.

flowermate v5 nano teardown shell removal 11

FM V5 Nano De-Shelled

Now for the good stuff – with the base screws and faceplate out of the way we can slide out the electronics enclosure.

flowermate v5 nano teardown shell 12

Thick Aluminum Chassis

The Nano’s shell is made of nice thick aluminum to hold up to daily pocket carrying. The total dimensions of the casing are only 3.5″ tall, 1.75″ wide and 0.75″ thick, making it one of the most compact hybrid vaporizers.

flowermate v5 nano teardown open chasis 13

 Guts and Glory

The FM Nano’s internals – the primary circuit board is connected with 4 screws. Most of the other goodies are still sealed in the enclosure.

flowermate v5 nano teardown screw removal shell 14

 Removing the Electronics

With the four retainer screws out of our way we can almost pull out the motherboard. It’s still stuck by the 3 different types of connecting wires. We’ll resist the urge to chop the wires… for now.

flowermate v5 nano teardown open chasis 15

 Chassis Separation 

After pulling the enclosure apart we get out first view at the airpath and heater. This new heating assembly looks much taller and beefier than the elements we saw in our Flowermate V5.0S Teardown and Mini Pro Teardown. The airpath is on the bottom right; when fully assembled it sits right below the heater.

flowermate v5 nano vaporizer teardown black ceramic chamber 22

Isolated Airpath and Spring Loaded Mouthpiece

We haven’t seen this before: the airpath tube is part of a spring loading mechanism for the mouthpiece. When you open the base door of the Nano this section pushes the mouthpiece out a little bit so you can remove it without the battery falling out. The picture on the left displays the airpath with the mouthpiece in place, the picture on the right is a close up of the airpath / spring mechanism.

The FM V5 Nano’s airpath is completely isolated from the battery and electronics. Air enters through the metal tube above the mouthpiece compartment and is tunneled directly into the heater above – perfect.

flowermate v5 nano vaporizer teardown circuitry 17

V5 Nano Connections

With the enclosure taken apart the brain of the FM Nano is finally free. The silver ring connected to the black wire pairs with the brass plate in the battery chamber to form the negative connection. The brass piece connected to the red wire is the positive connection point. Four thinner clear wires connect the heating assembly to the motherboard.

flowermate v5 nano vaporizer teardown circuitry front circut board back

V5 Nano Circuitry

The V5 Nano’s OLED screen, metal button actuators and Micro-USB connection are all on the front side of the primary circuit board. On the back of the board you can see some additional resistors, capacitors and transistors along with the wires that once connected to the heating assembly and battery poles.

flowermate v5 nano vaporizer teardown black ceramic chamber 19

Nano Chamber Assembly

Here is the Nano’s loading chamber disassembled. The metal spiral on the left sits below the chamber in the middle. The chamber itself consists of a black ceramic cylinder wrapped with a conductive element and then wrapped in thermal tape to maximize heat retention. The metal piece on the right is the threaded mouthpiece connection above the loading chamber.

flowermate v5 nano vaporizer teardown heating chamber hybrid 21

Nano Hybrid Heating Elements

A closer look at the Nano’s heating system. The metal spiral on the left is the convection element; it sits below the black ceramic chamber and heats the air traveling through the loading chamber. The piece on the right is the electrothermal pad that provides conduction heat through the black ceramic chamber.

flowermate v5 nano vaporizer teardown black ceramic chamber 22

Black Ceramic Heating Chamber

A look into the Nano’s unique black ceramic loading chamber. The electrothermal heating element wraps around the black ceramic and metal spiral below, resulting in an efficient mix of conduction and convection heating for thick vapor and uniform extraction.

Closing Thoughts

It’s fantastic seeing Flowermate breaking new ground and trying different things with their portables. The V5 Nano is the best looking and feeling Flowermate vaporizer to date and the hybrid heating outclasses the pure conduction heating of their previous V5 models both in vapor production and flavor. A removable 18650 battery is something we’ve been asking Flowermate to implement into their designs for years and we’re amped to finally see it happen. We’re not sure if the black ceramic chamber is a functional improvement over the previous white ceramic but it looks great and matches the aesthetic of the unit perfectly.

Any questions or feedback about our Flowermate V5 Nano Teardown? Please let us know in the comments section.

Check out our 4/20 Sale – we’re dropping new deals through April 20th! 

Hit us up on Reddit and YouTube for upcoming contests and video reviews and Instagram for weekly Live Streams every Thursday at 4:10 PST! 

Blog Previous Next

17 comments on Flowermate V5 Nano Teardown and Preview

  1. April 20, 2018 at 12:20 amBigjune48 Reply to Bigjune48
    Can you post a pic of chamber screen????
  2. April 20, 2018 at 1:51 pmfrank Reply to frank
    This is a great looking little vape. The fog has a real contender now. Will this drain the battery if you forget to shut it down like the Swift pro, or does it work more like the CF?
    • April 20, 2018 at 3:17 pmJake Reply to Jake
      It turns off entirely at the 5 minute cutoff so no wasted battery between sessions. =)
  3. April 20, 2018 at 5:27 pmbigjune48 Reply to bigjune48
    jake, without the ss screen pls
  4. April 21, 2018 at 4:25 amBigjune48 Reply to Bigjune48
    How's the draw resistance????
    • April 23, 2018 at 5:11 pmJake Reply to Jake
      A bit more restricted than the previous Flowermate models but not too tight; somewhat similar to the Boundless CF or CFX if you're familiar with either of those. We assume the change is to increase the energy efficiency of the convection air heating. =)
  5. April 26, 2018 at 1:51 pmKlaus Reply to Klaus
    Hi, can you specify what material is used for the metal spiral? Aluminum or Steel? Thx Klaus
    • April 28, 2018 at 3:54 pmJake Reply to Jake
      It's too tiny to be 100% positive, we'll need to check with FM. =)
  6. September 3, 2018 at 12:42 pmAnthony Reply to Anthony
    I'm having an issue with smoke/vapor rising from the chamber even after a few burn-offs and cleaning. I'm wondering if I got a fake unit or something, shouldn't the chamber be black? Since its black ceramic? Mine is a light grey.
    • September 5, 2018 at 5:14 pmZakk Reply to Zakk
      If you purchased it from us please email me pictures / video zakk@puffitup.com
  7. December 17, 2018 at 6:41 pmRusty Reply to Rusty
    I just picked up one of these and it came with two different sets of screens. One is obviously for the chamber, but what are the other smaller ones for? It looks like they would fit the mouth piece, but it seems impossible to access where that screen is to change it. Thank you in advance.
    • December 21, 2018 at 5:30 pmZakk Reply to Zakk
      Heyo Rusty! You are absolutely correct, the other screen is for the mouthpiece. To replace the mouthpiece screen remove the inner oring from the bottom of the mouthpiece. It is a different color black than the threaded portion. You should be able to easily remove it with the included Flowermate Tool :D Zakk
  8. March 20, 2019 at 10:40 amLuca109 Reply to Luca109
    Is there something like locktie on the screws so the warranty is gone when you disassamble it ?
    • April 2, 2019 at 3:58 pmZakk Reply to Zakk
      The company will be able to tell the vaporizer was opened, and opening it does void the warranty. Zakk
  9. April 8, 2019 at 9:22 pmRed Reply to Red
    When Im charging, (V5Nano) the screen displays the battery icon ok, but when it shows full is it really fully charged? I can get 2-3 sessions when the battery icon looks near dead. So....does the same apply at the top? How long should I keep it plugged in after the battery icon shows full? It says not to overcharge, so how long is safe? Please Im looking for answers to all these qs. Thanks