flowermate slick teardown main

Flowermate Slick Vaporizer Teardown! (Don’t try this at home)

The Slick Vaporizer is Flowermate’s newest convection / conduction hybrid with a removable 18650 battery and residue resistant black ceramic chamber. Let’s take a look inside!

Flowermate Slick Vaporizer

Magnetic Mouthpiece Cover

The Slick’s mouthpiece cover connects magnetically at the top of the unit to keep out any dust or pocket debris. Magnetic connections can’t wear down like threading plus they’re fun to play with after using this Slick vape.

Flowermate Slick Vaporizer Mouthpiece

Borosilicate Glass Mouthpiece

The mouthpiece is comprised of 2 sections: a connective base and a borosilicate glass mouthpiece. The stainless steel screen fits between the two to keep out ABV.

Flowermate Slick Vaporizer Battery Removed

Removable 18650 Battery

You can easily remove and swap out the Slick’s flat top 18650 battery by unscrewing the metal cover at the base of the unit. The cover piece acts as the negative connection between the battery and unit and is vented in case of battery failure.

Flowermate Slick Vaporizer Battery

2500 mAh Battery Capacity

The Slick vaporizer includes a custom wrapped 18650 battery with ICR chemistry, 2500 mAh charge capacity, and a max output of 20 amps. 2500 mAh is good for around an hour of vaping on a full charge which is standard for single 18650 vapes. 20A output is huge –¬†we’re not positive how much of that amperage the Slick utilizes but it’s able to fully heat in a little over half a minute: very respectable.

Flowermate Slick Vaporizer Shell

Laminated Carbon Fiber Exterior

The body of the Flowermate Slick is made of aluminum with a protective layer of carbon fiber laminate over top. Raw aluminum is lightweight and impact resistant but prone to surface scratching. Laminated carbon fiber is much more scratch-resistant and light surface scratches are barely visible.

WARNING: Do not follow along past this point, this is where warranty coverage ends.

Flowermate Slick Vaporizer Warranty Ends

Flowermate Slick Vaporizer top airpath and silicone cushion

Going Topless

The point of no return. We shoved a scientific grade screwdriver into the top piece and pried it out scientifically. The top piece is made of two hard plastic sections surrounding the mouthpiece magnet.

Flowermate Slick Vaporizer Button Removal

Button Removal

We were able to pry out the Flowermate Slick’s button enclosure without any damage. In the opening you can see the oval shaped actuator that registers button presses.

Flowermate Slick Vaporizer Breaking the shell beyond repair

Flowermate Slick Vaporizer Shell open

Shelling the Slick

Here’s where things got difficult – the internal chassis is friction fitted inside the aluminum and carbon fiber body. The chassis fit too tightly to remove by force so we had to bring out the official PIU rotary tool for some custom modification to the shell. We ended up breaking the shell beyond repair, just like in the Aero Teardown!

Flowermate Slick Vaporizer heat tape

Flowermate Slick Vaporizer Internal Chassis

Up in Them Guts

With the aluminum and carbon fiber shell cut away we only need to remove a layer of thermal tape to gain access to the internal chassis and electronics. On the far left of the second picture you can see the negative connection point of the battery compartment. The gold piece in the center is the positive connection point. To the right of the positive connection is the primary circuit board. The haptic feedback module can be seen above the circuit board and the heater is to the right.

Flowermate Slick Vaporizer Internal Chassis top open

Flowermate Slick Vaporizer Chassis Internal

Isolated Airpath Confirmed

The Slick’s chassis is comprised of two halves held together with seven tabs. The chassis seals airflow in the top section of the unit a safe distance away from the electronics and battery. Fresh air enters from the top and travels down below the barrel until it reaches the openings below the heater.

Flowermate Slick Vaporizer Battery Connection

Flowermate Slick Vaporizer Chamber Insulation

Flowermate Slick Vaporizer Chamber and Circuitry

Slick Electronics

The top picture is a closer look at the positive connection point for the battery which appears to be made of brass. The second picture shows the cotton thermal wrap that surrounds the heating chamber. In the bottom left of the third picture you get a closer look at the vibration module. Above that you can see all the connections on the primary circuit board including the Micro-USB port. To the right is the heating chamber unwrapped and pulled from its base.

Flowermate Slick Vaporizer Chamber Open

Convection / Conduction Hybrid Heater

Here is the Slick’s entire heating assembly taken apart. From left to right you can see the silicone base, the metal spiral convection element, and the heating chamber. The black ceramic chamber is heated by a thin, battery efficient electrothermal wrap. The metal spiral rests in the center of the silicone piece being passively heated by the chamber. Fresh air is forced around the hot spiral and rapidly raises in temperature before passing up through your material. This style of hybrid heating provides the flavor and extraction benefits of convection with the low battery draw of conduction.

Flowermate Slick Vaporizer Black Ceramic Chamber

Black Ceramic Loading Chamber

Instead of standard white ceramic the Slick vaporizer uses the black ceramic loading chamber found in the Flowermate V5 Nano. Black ceramic is claimed to be more buildup resistant and easier to clean. We’re not positive we’re getting less buildup or if it’s just less visible but the chamber is definitely a snap to clean out with iso and q-tips.

We hope this teardown was informative about the materials and build of the Flowermate Slick Vaporizer. If you have any questions please let us know in the comment box below!

Stop by our Youtube, Reddit and Instagram for more PIU exclusive content!

Blog Previous Next

One comment on Flowermate Slick Vaporizer Teardown! (Don’t try this at home)

  1. […] tuned for future Teardowns! In the past we’ve done the FIERCE, SLICK, and […]